COLUMBIA
LIVE EDGE SLABS
Get a Quote

COLUMBIA, MISSOURI · WOOD WITH CHARACTER

Live Edge Slabs in Columbia, MO

A natural edge. A grain pattern all its own. Find the wood for your table, counter or next project.

Get a Quote Estimate your slab budget →
Measure the narrow and wide points of a live edge slab to estimate its average width.
Measure the wood. Plan the piece.
01

Table slabs

Find the proportions for your dining table, desk or coffee table.

02

Bar tops & counters

Choose a slab for a room you use every day.

03

Slab woods

Compare the color, grain and character of Missouri woods.

We sell live edge slabs sawn from mid-Missouri trees at a working sawmill near Columbia. Pick out a slab for a dining table, desk, bar top or shelf, get its measurements and price before you drive, and pick it up near Columbia instead of paying freight on a heavy slab.

Every slab here comes from a tree that grew in this part of Missouri. When we know the town or county a log came from, we'll tell you.

Slabs on our racks

Every slab we sell has its own size, dryness and price, and we'll send them before you make the drive. Our slabs page explains how to read those numbers.

When you look at a slab, check four things before you fall for the grain:

  • Length first. Extra length can be trimmed off; missing length can't be added. Leave a few inches to trim checked ends.
  • Width at the narrow end. That's the width you can count on for a tabletop.
  • Cracks and soft spots. Small end checks are normal. Deep cracks need bow ties or epoxy, and soft, punky wood needs cutting out.
  • Dryness. Ask whether it's green or air-dried, and plan your project around the answer.

Tell us the size you need. We'll tell you what fits from the racks, or what we could saw for you.

Slab woods from mid-Missouri

Missouri grows a lot of good slab wood, and Missouri is walnut country. Walnut is the slab most people ask about first, but it isn't the only good choice.

  • Black walnut: chocolate-brown heartwood with pale sapwood near the edge. The classic table slab.
  • White oak: hard, heavy and tight-grained. Holds up on bars and busy tables.
  • Sycamore: often the widest slabs from local trees, with a fine, speckled figure when cut through the center of the log.
  • Maple: pale wood, sometimes with dark spalting lines or streaks.
  • Ash, elm and cherry: ash looks like a lighter oak, elm has wild interlocked grain, and cherry deepens in color the longer it sees daylight.
  • Eastern red cedar: red and cream, fragrant, and usually narrow. Good for shelves and benches.

Choosing between them usually comes down to two questions: what color do you want in the room, and how hard will the top be used? A busy kitchen table rewards a hard, tight-grained wood. A desk or a side table can lean on looks alone, so softer woods with wild figure are fair game there, and they often cost less.

Our slab species comparison lines them up by color, hardness, movement and price.

What people build with them

Most slabs end up as one of these:

  • Dining tables. A single wide slab, or two slabs bookmatched side by side. See choosing a slab for a table for sizes by number of seats.
  • Coffee tables and desks. Shorter pieces, often with more character: a crotch, a knot or a natural edge with a curve.
  • Bar tops, islands and vanities. Long, narrow slabs from straight trunks. Our bar tops and countertops page covers lengths, species and finishes for wet areas.
  • Floating shelves and benches. Offcuts and narrow slabs work well here and cost less.
  • Epoxy river tables. A pair of slabs set edge to edge with a channel of resin between. Our guide to choosing a slab for an epoxy river table explains what to look for.

Dry, flat and ready, or rough: what you're buying

Two things decide how much work a slab needs before it becomes furniture: how dry it is and how flat it is.

Dryness. A slab straight off the mill is green, full of water. As it dries it shrinks, and it can cup, twist or check. Air-dried wood in Missouri is still wetter than wood that has settled indoors, so a slab that comes into a heated house keeps drying, and moving, for a while.

Thick slabs take years to air-dry. Our guide on how long a slab takes to dry goes into thicknesses, and how to check if a slab is dry shows what to look for before you buy.

There's no kiln at our mill, so every slab is sold green or air-dried, and you'll know which before you pay.

Flatness. A sawn slab has saw marks and is rarely perfectly flat, especially after drying. Most get flattened on both faces with a router sled or a wide planer before finishing. That takes some thickness off, and more if the slab has cupped or twisted. If you'd like to do it yourself, see flattening a slab with a router sled.

How pickup works

  1. Look through the slabs page, or tell us what you need on the request form.
  2. We reply with the slabs that fit, their sizes and a price.
  3. You pick it up at our yard near Columbia. Bring a friend for the lifting and a truck or trailer that can carry it flat.

Slab prices

Most slab pricing starts from board feet, a volume figure worked out from length, average width and thickness. Species, width, figure and dryness then move the price up or down.

Across the country, walnut is the priciest common slab wood at roughly $10 to $25 per board foot. That's a national figure, not ours. Our pricing page has the full table, worked examples and a slab price calculator.

Ask About a Slab

Send your project, the size and the wood you like, and we'll match a slab to it.

Ask About a Slab

MAKE ROOM FOR SOMETHING ORIGINAL

Your next project
starts with a slab.

Tell us the size, the wood and what you have in mind.

Get a Quote